This is a simple breakout board for the popular XBee product from Digi. This board breaks out all 20 pins of the XBee to a 0.1" standard spacing dual row header. The spacing between 0.1" headers is 0.5" making it breadboard DIP friendly. We highly recommend using the female sockets to avoid having to solder the XBee permanently to the breakout board. This is the PCB only. Please order the accompanying 2mm sockets (you’ll need 2!) and 0.1" headers below.

This is a simple to use, USB to serial base unit for the Digi XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, attach a mini USB cable, and you will have direct access to the serial and programming pins on the XBee unit.

The highlight of this board is an FT231X USB-to-Serial converter. That’s what translates data between your computer and the XBee. There’s also a reset button, and a voltage regulator to supply the XBee with plenty of power. In addition, there are four LEDs that’ll help if you ever need to debug your XBee: RX, TX, RSSI (signal-strength indicator), and power indicator.

This board also breaks out each of the XBee’s I/O pins to a pair of breadboard-compatible headers. So if you want to make use of the XBee’s extended functionality, you can solder some header pins into those, or even just solder some wire.

Not sure which XBee module or accessory is right for you? Check out our XBee Buying Guide!

Note: There is no XBee included with this Explorer USB. Check the Recommended Products section below for different options.

This low cost XBee USB Adapter Board comes in partially assembled kit form and provides a cost-effective solution to interfacing a PC or microcontroller to any XBee or XBee Pro module. The PC connection can be used to configure the XBee Module through Digi's X-CTU software. Works with XBee series 1 and 2 as well as Pro modules

By using this adapter board you can provide an easy interface to the XBee or XBee Pro modules by converting the 2mm pin spacing to breadboard friendly 0.100" spacing. The adapter board also provides a means to connect pluggable wires or solder connections and also provides mounting holes. Note: This product from Parallax uses genuine FTDI chips 10/23/14 (read more).

Features:

Provides an easy interface to configure XBee Modules using Digi's X-CTU software

Converts XBee 2mm pin spacing to 0.100" pin spacing

4 status indicator LEDs for Power, RSSI, Associate and mode (sleep/ON)

Provides easy pluggable wire or solder connections

Includes mounting holes

Pin-out compatible with our other XBee Adapter boards

Partially assembled kit form for flexible configuration

Kit Contents:

(1) XBee Adapter Board PCB

(2) 10-pin 2mm sockets - these are soldered into the board.

(1) 40-pin SIP header

Tools Required:

Soldering Iron

Solder

Flux

Diagonal cutters or Exacto knife

Key Specifications:

Power requirements: 5.0V from USB or VDD pin, 3.3V generated on-board

Communication: Serial pass-through to XBee module/USB to Host PC

Dimensions: 1.51 x 1.00 x 0.58 in* (38.3 x 25.6 x 14.8 mm*)

* when headers are attached

Operating temp range: -40 to +158F (-40 to +70C)

Works with all XBee & Pro modules!

You'll need a USB cable with a mini-b connector on it to plug this into your computer! We have such an item in the shop, or you can look around the house, they're often used for digital cameras.

This adapter board is designed to make adding wireless point-to-point or mesh networking easy. I looked at all the XBee adapter boards available and decided to design something better:

Onboard 3.3V regulator to cleanly power your XBee, up to 250mA

Level shifting circuitry means that its trivial to connect it to 5V circuitry such as an Arduino without risk of damage

Two LEDs, one for activity (RSSI), the other for power (Associate)

10-pin 2mm sockets included to protect the modem and allow easy swapping, upgrading or recycling

All the commonly used pins are brought out along the edge, making it easy to breadboard or wire up

Specifically created for use with an FTDI cable to connect to a computer via USB. This means that you can use or upgrade the adapter with a computer simply by plugging in a cable

Works with XBee series 1 and 2 as well as Series 1&2 Pro modules

The kit includes a PCB and all components necessary to build the adapter, unassembled. Tools are not included. This kit is really easy and will only take 15 minutes to build, even if you've never soldered before.

Please note that the adapter does not include an XBee module, they must be purchased separately. Check out this page for a comparison of all the XBee's available. If you want to connect this up to a computer's USB port you'll need a FTDI cable or FTDI friend (also not included)

For more information, check out the project page for instructions, documentation, tutorials and example code!

This is the XBee WiFi Module with PCB Antenna from Digi. XBee WiFi embedded RF modules provide simple serial to IEEE 802.11 connectivity. By bridging the low-power/low-cost requirements of wireless device networking with the proven infrastructure of 802.11, the XBee WiFi creates new wireless opportunities for energy management, process and factory automation, wireless sensor networks, intelligent asset management and more. Focused on the rigorous requirements of these wireless device networks, the module gives developers IP-to-device and device-to-cloud capability.

XBee modules offer developers tremendous flexibility and are available in surface mount and through-hole form factors. The XBee WiFi shares a common footprint with other XBee modules. This allows different XBee technologies to be drop-in replacements for each other.

As a member of the XBee family, the XBee WiFi combines hardware with software for a complete modular solution. XBee WiFi modules are designed to communicate with access points in existing 802.11 infrastructures. Developers can use AT and API commands for advanced configuration options.

Note: If you are using these outside of the United States, please check with your local laws regarding radio communication.

Features

3.3V @ 309mA

72Mbps Max data rate

Antenna Type: PCB (Embedded)

Fully FCC certified

4 12-bit ADC input pins

10 digital IO pins

13 Channels

AT or API command set

This is the XBee WiFi Module with wire antenna from Digi. XBee WiFi embedded RF modules provide simple serial to IEEE 802.11 connectivity. By bridging the low-power/low-cost requirements of wireless device networking with the proven infrastructure of 802.11, the XBee WiFi creates new wireless opportunities for energy management, process and factory automation, wireless sensor networks, intelligent asset management and more. Focused on the rigorous requirements of these wireless device networks, the module gives developers IP-to-device and device-to-cloud capability.

XBee modules offer developers tremendous flexibility and are available in surface mount and through-hole form factors. The XBee WiFi shares a common footprint with other XBee modules. This allows different XBee technologies to be drop-in replacements for each other.

As a member of the XBee family, the XBee WiFi combines hardware with software for a complete modular solution. XBee WiFi modules are designed to communicate with access points in existing 802.11 infrastructures. Developers can use AT and API commands for advanced configuration options.

Note: If you are using these outside of the United States, please check with your local laws regarding radio communication.

Features

3.3V @ 309mA

72Mbps Max data rate

Antenna Type: Integrated Wire

Fully FCC certified

4 12-bit ADC input pins

10 digital IO pins

13 Channels

AT or API command set