PiJack is a HAT (yes, a proper HAT, not a pHAT!) add-on board for the Raspberry Pi Zero mini computer that makes connecting your Pi Zero to the Internet via Ethernet super simple. If you're fed up with flaky WiFi and want your Pi Zero to be online all the time, then this HAT is for you!

PiJack is a neat little board with an Ethernet controller and standard RJ45 connector so you can hook your Pi up to your home or office network using standard Ethernet cables. PiJack is ready to go – there's no special software or drivers to install. It works right out of the box with Raspbian – simply attach PiJack to your Pi's GPIO header and plug it in!

Features:

10Mbps Ethernet connection

Two blinky LEDs for connection status

HAT-standard-compliant EEPROM makes setup automatic, works straight away with Raspbian!

Uses the Pi Zero's GPIO pins, your USB connector is still free for something else!

Note: Pi Zero and Ethernet cable not included!

PiJack is well engineered and uses high quality components and connectors (that won't snap off the first time you use it!). PiJack is built in the EU, and every board is tested to make sure it'll work for you first time.

Looking for an unashamedly old school LED matrix display board? Lookie here! The Pimoroni Micro Dot pHAT is made up of six red LED matrices, each 5x7 pixels (for an effective display area of 30x7) plus a decimal point, using the beautiful little Lite-On LTP-305 matrices.

Perfect for building a retro scrolling message display, a tiny 30-band spectrum analyzer, or a retro clock. Far out!

As with the other pHATs, it works with all of the 40-pin Raspberry Pi variants - 3/2/B+/A+/Zero - but using it with the Pi Zero makes for a super-tiny package.

Features:

3x onboard IS31FL3730 LED matrix driver chips

Drives up to 6 x LTP-305 red LED matrices

Up to 30x7 pixels (5x7 per matrix plus a decimal point)

Kit includes:

Assembled Micro Dot pHAT PCB

2x20 0.1" female GPIO header

6 Red LTP-305 LED modules

Micro Dot pHAT also works well with other pHATs and HATs. You could use it in combination with pHAT DAC to display the audio spectrum, or with Enviro pHAT to display its temperature, pressure and light readings. Give it a try!

Note: These pHAT boards require you to solder on the headers and LTP-305 modules (through-hole components). Works with any 40-pin Raspberry Pi variant.

The Pimoroni Speaker pHAT crams an I2S DAC and mono amplifier, a tiny 8Ω 2W speaker, and a 10 LED bar graph all onto one teeny little pHAT. It's the neatest way to add audio to your Pi project, and its beautiful artwork evokes an 80s boombox!

Pimoroni isn't claiming audiophile sound quality, but it's perfect for fun little projects where you want to add sound output – speech, notification sounds, or light music, for example.

Why not combine it with a little USB microphone to make a tiny voice-activated assistant in the style of Amazon's Echo? Or set up a simple Flask API and send audio notifications to it from IFTTT with a simple HTTP request.

It comes as a kit, so you'll have to solder on the female 40 pin header, and screw and solder the speaker on. Check out Pimoroni's assembly guide for more details.

Features:

I2S audio DAC with 3W mono amplifier (MAX98357A)

Default output of 0.45W/26.5dB

8Ω 2W Mylar speaker

Routed holes to channel sound

10 bright white bar graph LEDs

SN3218 LED driver chip

Compatible with Raspberry Pi 3, 2, B+, A+, and Zero

Female header and speaker require soldering (includes a piece of bare wire to solder the speaker)

Kit includes:

Speaker pHAT

8Ω 2W Mylar speaker

2x20 pin female header

5cm 24AWG bare wire

4x M2x8 black nylon bolts

8x M2 black nylon nuts

Note: Pi Zero not included!

If you didn't think that the Raspberry Pi Zero could possibly get any better, then boy do we have a pleasant surprise for you! The new Raspberry Pi Zero W offers all the benefits of the Pi Zero v1.3, but with one big difference – built-in WiFi!

More specifically, this giant upgrade is the addition of a BCM43143 WiFi chip BUILT-IN to your Raspberry Pi Zero – just like the Pi 3! No more pesky WiFi adapters - this Pi is WiFi ready. There’s also Bluetooth Low Energy (BLE) on board making the Pi an excellent IoT solution (BLE support is still in the works, software-wise).

We also have a basic pack, budget pack and starter pack with all the essentials to get your Zero W up and running.

Note: Due to popular demand, there might be some delay in shipping products containing Pi Zero W!

At first glance, the Pi Zero W looks just like the Raspberry Pi Zero v1.3 we know and love. But when we started to think of the added convenience of not having to worry about hooking up a WiFi dongle or Ethernet cable - and what a well-chosen set of accessories could add - we realized the appeal. And then we saw the price...could it be true? Yes!

This is the slimmest, most pared down Raspberry Pi to date. It's kind of like the little cousin to the Pi 3 - with just a micro SD card slot, a mini HDMI port, two micro USB ports (one for power, one for USB), and 512MB of RAM. It has a single-core 1 GHz processor chip, similar to the Pi A+ and B+.

The best part about all this is that the Pi Zero W keeps the same shape, connectors, and mounting holes as the Pi Zero v1.3. 99% of cases and accessories will still be fully compatible with both the Pi Zero W and v1.3 - though if you have a case with a metal top there might be some WiFi chip difficulties.

Please note - even though there's built-in WiFi, the Pi Zero W is quite minimal and requires a few accessories to turn it into a computer! At a minimum we recommend:

A good quality 5V power supply - Either a 5V 2A with cable or combine a  5V 1A power supply and a Micro B USB cable - this will allow you to power the Zero from a wall adaper. It is not suggested to power the Zero from a computer USB port as the voltage often sags and can cause SD card corruption!

4GB+ SD Card with Operating System - You can grab a ready-to-go Raspbian card that has the correct firmware for the Zero here. Or you can pick up an 8G card with NOOBS 2.0. Or use a blank 4G SD card and burn in Raspbian Wheezy and update the firmware. Make sure you have the latest version!

Mini HDMI to HDMI Adapter - Will let you convert the little port on the Zero to a standard sized HDMI jack. You can get 1080P HDMI video + audio out of this little computer!

USB OTG Cable - Lets you plug in a normal USB device such as WiFi dongle, USB hub, keyboard, mouse, etc into the Zero.

USB Console cable - if you're not going to stick an HDMI monitor on there, then this is essential, you connect the wires to the GPIO pins and log in over a serial console. Its the easiest & fastest way to get on your Pi

2x20 Male header strip - Solder this in to plug in Pi HATs, GPIO cables, etc as you would into a normal Pi. (We also have a 2x20 Female and 2x20 Female right-angle style for more exotic connecting)

To keep the price and size as small as possible, there is a spot on the Zero for a 2x20 pin header. This header is not included or soldered on. Creative individuals can easily solder in a set of 2x20 male header strip so you can plug in any sort of Pi HAT or other plug-in topper.  Or, go with a 2x20 female header and plug the Pi Zero directly into an Adafruit Cobbler or T-Cobbler.  

We also strongly recommend some other parts and pieces to make your Pi Zero computing experience easier:

Adafruit Pi Zero Enclosure - Adafruit's classic, sturdy plastic enclosure. Keeps your Pi Zero safe and sleek.

Pi Zero Protector - Keep your Pi Zero safe while handling with this simple sandwich-style acrylic case.

USB Powered Hub - So you can plug in any kind of USB devices without overloading the Zero's power supply. (You can also, ironically, power the Zero from the hub itself by plugging in a micro USB cable into the hub)

Mini Wireless Keyboard w/Trackpad - Requires only one USB port, which makes it a great match for the Pi Zero

Wireless Keyboard + Mouse set - Also requires only one USB port, but for everyday use.

Pi Cobbler or T-Cobbler - When paired with the male or female 2x20 pin header, you can use your Zero with a breadboard to connect sensors, LEDs, motors and more!

Ethernet Hub and USB Hub w/ Micro USB OTG Connector - One can never have enough socks, or USB ports. Add some more USB and Ethernet capability to your Raspberry Pi Zero if you're an Ethernet enthusiast!

Please note: Some boards are made in the UK, some in China. WE DO NOT KNOW IN ADVANCE WHICH ONES YOU MAY RECEIVE!

One can never have enough socks, or USB ports. Add some more USB capability to your Raspberry Pi Zero with the Zero4U!

This is a 4-port USB hub for Raspberry Pi Zero, and it can be mounted back-to-back onto a Pi Zero. The 4 pogo pins on the back will connect the PP1, PP6, PP22 and PP23 testing pads on your Raspberry Pi Zero – no soldering required!

This item can only work with the Zero W if a ferrite ring is installed!

The USB hub will take power directly from your Pi Zero, so you don’t need to power the USB hub separately. However you can use the JST XH2.54 connector on board as an alternative power input port. The blue onboard LED is the power indicator, and will light up when power is connected. Each USB port uses a dedicated white LED as a transaction indicator, and a dedicated electrolytic capacitor to help stabilize the output voltage.

If you use this USB hub with other types of computers, you can use a USB cable (not included) to connect the onboard mini-USB port to the up-stream USB port.

Kit includes:

4-port USB hub board x 1

Plastic spacer x 4

M2.5 plastic screw x 4

M2.5 plastic nut x 4

Note: This version of Zero4U only works with the Raspberry Pi Zero v1.3 (with camera connector).

Note: As of 3/29/2017, this ships with a small Ferrite ring in each Zero4U package, in order to support the newly released Raspberry Pi Zero W. The user can put that Ferrite ring on the pogo pins to avoid the interference from the on-board antenna.