Login
  • Login
3 items has been found
ImageItemLocationAvailable
Serial Enabled 16x2 LCD - White on Black 5V

This is the latest evolution of our serial LCD. Included on a single board is a 16x2 LCD and an embedded circuit based around a PIC 16F88. The on-board PIC takes a TTL serial input and prints the characters it receives onto the LCD. The installed firmware also allows for a number of special commands so you can clear the screen, adjust the backlight brightness, turn the display on/off, and more.

Communication with SerLCD requires 5V TTL serial at a default baud rate of 9600bps (8-N-1). You can adjust the baud to any standard rate between 2400 and 38400bps. The power (VDD), ground (GND) and RX pins are all broken out to both a 0.1" pitch header as well as a 3-pin JST connector.

SerLCD has the ability to dim the backlight to conserve power if needed. There is also a potentiometer on the back of the display to adjust the contrast.

Features

Embedded PIC 16F88 utilizes onboard UART for greater communication accuracy

Adjustable baud rates of 2400, 4800, 9600 (default), 14400, 19200 and 38400

Operational Backspace

Greater processing speed at 10MHz

Incoming buffer stores up to 80 characters

Backlight transistor can handle up to 1A

Pulse width modulation of backlight allows direct control of backlight brightness and current consumption

All surface mount design allows a backpack that is half the size of the original

Faster boot-up time

Boot-up display can be turned on/off via firmware

User definable splash screen* PCB: 103x36mm

LCD: 71.4x26.4mm

https://www.sparkfun.com/products/9395
sparkfun monochrome display character power board
D-14
2/2
Graphic LCD 84x48 - Nokia 5110

The Nokia 5110 is a basic graphic LCD screen for lots of applications. It was originally intended to be used as a cell phone screen. This one is mounted on an easy to solder PCB.

It uses the PCD8544 controller, which is the same used in the Nokia 3310 LCD. The PCD8544 is a low power CMOS LCD controller/driver, designed to drive a graphic display of 48 rows and 84 columns. All necessary functions for the display are provided in a single chip, including on-chip generation of LCD supply and bias voltages, resulting in a minimum of external components and low power consumption. The PCD8544 interfaces to microcontrollers through a serial bus interface.

Note: There may be small blemishes on these screens as they are surplus.

Note: Your screen may or may not have a diode on the PCB. It does not affect performance and will vary depending on our shipment.

Features

45x45mm

https://www.sparkfun.com/products/10168
sparkfun monochrome display power component voltage
D-14
1/1
SparkFun Micro OLED Breakout

The SparkFun Micro OLED Breakout Board breaks out a small monochrome, blue-on-black OLED. It’s “micro”, but it still packs a punch – the OLED display is crisp, and you can fit a deceivingly large amount of graphics on there. This breakout is perfect for adding graphics to your next Arduino project, displaying diagnostic information without resorting to serial output, and teaching a little game theory while creating a fun, Arduino-based video game. Most important of all, though, is the Micro OLED is easy to control over either an SPI or I2C interface.

You may be asking yourself, “Why does this board look so familiar?” Yes, this is essentially a MicroView without the Arduino portion. We understand that sometimes you just need a breakout, an open door for you to explore the possibilities of a super small OLED screen. Speaking of, the screen on this breakout is only 64 pixels wide and 48 pixels tall, measuring 0.66" across.

In total, the Micro OLED Breakout provides access to 16 of the OLED’s pins. Fortunately, though, you’ll only need about half of them to make the display work. The top row of pins (GND-CS) breaks out everything you’d need to interface with the OLED over an SPI or I2C interface. The pins on the bottom (D7-vB) are mostly only used if you need to control the display over a parallel interface. This board operates at 3.3V with a current of 10mA (20mA max).

Get Started with the SparkFun Micro OLED Breakout Guide

Features

Operating Voltage: 3.3V

Screen Size: 64x48 pixels (0.66" Across)

Monochrome Blue-on-Black

SPI or I2C Interface

https://www.sparkfun.com/products/13003
sparkfun monochrome oled breakout i2c display lcd microview
D-14
1/1

Item Detail

SensiLab Inventory

© SensiLab Monash University 2017-2025